NS-V-14-150 Variable Force Gas Strut

TIER PRICES
  • QUANTITYPRICE
  • 6 + £34.69
  • 20 + £29.22
  • 50 + £25.56
  • 100 +Contact Us
CODE
NS-V-14-150
OLD CODE
SD04-150
PRICE £36.52
Metrol Springs
NS-V-14-150
/media/catalog/product/n/s/ns-v-14-150100.jpg
Please remember to check stock below:
  • Product code
    Product Description
    Stock Status
  • NS-V-14-150
    NS-V-14-150 Variable Force Gas Strut
    50+
  • B13
    Ball Joint End Fittings with 10mm Thread full range-M10-25mm-16mm
    50+
  • B13-A
    Ball Joint End Fittings with 10mm Thread full range-M8-25mm-13mm
    1 - 25
  • B14
    Ball Joint End Fittings with 10mm Thread full range-M10-30mm-16mm
    50+
  • B14-A
    Ball Joint End Fittings with 10mm Thread full range-M8-30mm-13mm
    50+
  • B15
    Ball Joint End Fittings with 10mm Thread full range-M10-35mm-16mm
    50+
  • B15A
    Ball Joint End Fittings with 10mm Thread full range-M8-35mm-13mm
    50+
  • E11
    Eye End Fittings with 10mm Thread full range-10mm-22mm
    50+
  • E12
    Eye End Fittings with 10mm Thread full range-10mm-30mm
    50+
  • E13
    Eye End Fittings with 10mm Thread full range-10mm-35mm
    50+
  • C3
    Clevis Fork with 10mm Thread C3
    50+
  • RE12
    Rose Eye End Fitting with 10mm Thread
    50+
  • BRK-4A
    BRK-4A 13mm Circular Bracket with 41mm Fixing Centres
    50+
  • BRK-6A
    BRK-6A 13mm Internal Right Angle Bracket with 38mm Fixing Centres
    50+
  • BRK-6R-A
    BRK-6RA 13mm External Right Angle Bracket with 38mm Fixing Centres
    50+
  • BRK-7A
    BRK-7A 13mm Triangular Bracket with 55mm Fixing Centres
    50+
  • BRK-11
    BRK-11 16mm Triangular Bracket with 51mm Fixing Centres
    50+
  • BRK-8
    BRK-8 8mm U Shaped Bracket with 50mm Fixing Centres
    50+
  • BRK-8-90
    BRK-8-90 8mm U Shaped Bracket with 51mm Fixing Centres
    50+
  • C3CLIP
    C3CLIP 10mm Clevis Fork Clip
    50+
  • DC-SD04-BLK
    14mm Rod Dust Cover for 27mm Body Gas Struts
    50+
  • PPT-14-150
    14mm Plastic Protection Tube-150mm
    1 - 25
  • MPT-14-150
    14mm Metal Protection Tube-150mm
    1 - 25
  • MLT-14-150
    14mm Metal Safety Locking Tube-150mm
    26 - 50
More Information
Stroke 150mm
Extended Length 380mm
Rod Diameter 14mm
Body Diameter 27mm
Force Range 150 - 2500N

INSTALLATION INSTRUCTIONS

For standard compression gas struts we advise the use of ball joints to alleviate possible side loading, and uneven wearing of the piston rod/seals. Install the strut, piston rod down, for optimum lubrication of the guide and sealing system at all times. Always install the strut in its relaxed state. It is advisable to keep the strut in a single plane of movement. Failure to adhere to this advice may result in a reduced lifespan of the strut. Ensure that the end fittings are tightly fastened onto the thread of the gas struts prior to fitting. If the end fittings require aligning, the piston rod of the gas strut can rotate inside the body (cylinder). Place and hold the piston end fixing on a flat surface, grip the cylinder and firmly twist it until the end fitting is aligned correctly.

FITTING BRACKETS

When utilising a bracket with a ball stud/end, the procedure to fit it to the relevant ball joint fitting is as follows:

  • Remove the retaining clip from the ball socket by rotating it from around the collar of the socket, and then pull it out from the two locating holes.
  • Ensure the ball socket is fully tightened onto the thread of the strut. Then, using a vice or pair of pliers, grip the ball stud and with a rotating motion, remove the ball stud from the socket.

FORCE ADJUSTMENT

  • Fit the gas struts with the cylinder uppermost; this prevents oil escaping while venting, and keeps the internal seals lubricated for optimum lifespan.
  • Using the allen key provided, undo the grub screw anti-clockwise a quarter turn and vent gas for 1 second, retightening the grub screw. Do not over tighten the grub screw.
  • Repeat this process on the second gas strut, venting an equal amount. Only release the pressure in short bursts to avoid venting too much gas. Each 1 second burst will lower the force by approximately 20N - 50N depending on the range.
  • Test the application by attempting to close the panel and repeat the venting process if the struts are still too powerful.
  • Once the gas struts have been adjusted, gently brush the grub screw with washing up liquid. If gas can be seen bubbling through the liquid then the grub screw requires further tightening.

For advice on how to safely mount gas struts call our technical line: 01604 499332.

Gas struts are filled with high pressure nitrogen, they should be protected from damage; never open, modify, drill, weld or subject gas struts to excessive heat.

Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account
Struts End Fittings
Struts Brackets
Struts Accs
Catalogues
Documents
Struts Variable
Struts Variable
  • NS-V-14-150
Struts End Fittings
  • B13
  • B13-A
  • B14
  • B14-A
  • B15
  • B15-A
  • E11
  • E12
  • E13
  • C3
  • RE12
Struts Brackets
  • BRK-11
  • C3-CLIP
Struts Accs
  • MPT-14-150
  • MLT-14-150
  • PPT-14-150
  • DC-SD04-BLK