NS-SS-V-8-200 Stainless Steel 316 Variable Force Gas Strut

CODE
NS-SS-V-8-200
OLD CODE
SDSS-02-200
PRICE £27.17
VOLUME DISCOUNTS
  • QUANTITYPRICE
  • 6 + £25.81
  • 20 + £21.74
  • 50 + £19.02
- +
Metrol Springs
NS-SS-V-8-200
/media/catalog/product/n/s/ns-ss-v-8-200100.jpg

OPTION PREVIEW

  • Product code
    Product Description
    Stock Status
  • NS-SS-V-8-200
    NS-SS-V-8-200 Stainless Steel 316 Variable Force Gas Strut
    26 - 50
  • SSB1
    Stainless Steel Ball Joint End Fittings with 6mm Thread-M6-18mm-10mm
    50+
  • SSB3
    Stainless Steel Ball Joint End Fittings with 6mm Thread-M6-25mm-10mm
    50+
  • SSB5
    Stainless Steel Ball Joint End Fittings with 6mm Thread-M8-18mm-10mm
    50+
  • SSB7
    Stainless Steel Ball Joint End Fittings with 6mm Thread-M8-25mm-10mm
    50+
  • SSE1
    Stainless Steel Eye End Fitting with 6mm Thread-8.5mm-18mm
    50+
  • SSE2
    Stainless Steel Eye End Fitting with 6mm Thread-8.5mm-20mm
    50+
  • SSE3
    Stainless Steel Eye End Fitting with 6mm Thread-8.5mm-22mm
    50+
  • SSE4
    Stainless Steel Eye End Fitting with 6mm Thread-8.5mm-25mm
  • SSE5
    Stainless Steel Eye End Fitting with 6mm Thread-8.5mm-30mm
    50+
  • SSC1
    Stainless Steel 316 Clevis Fork with 6mm Thread
    50+
  • SSBRK-2
    SSBRK-2 Stainless Steel 316 10mm Circular Bracket with 20mm Fixing Centres
    50+
  • SSBRK-3
    SSBRK-3 Stainless Steel 304 10mm Triangular Bracket with 22.5mm Fixing Centres
    50+
  • SSBRK-4
    SSBRK-4 Stainless Steel 304 10mm Circular Bracket with 41mm Fixing Centres
    50+
  • SSBRK-052-L
    SSBRK-052-L Stainless Steel 316 10mm Internal Right Angle Bracket with 50.6mm Fixing Centres
    50+
  • SSBRK-052-R
    SSBRK-052-R Stainless Steel 316 10mm External Right Angle Bracket with 50.6mm Fixing Centres
    5 - 25
  • SSBRK-6
    SSBRK-6 Stainless Steel 304 10mm Internal Right Angle Bracket with 38mm Fixing Centres
    50+
  • SSBRK-7
    SSBRK-7 Stainless Steel 304 10mm Triangular Bracket with 55mm Fixing Centres
    50+
  • SSBRK-8
    SSBRK-8 Stainless Steel 304 8mm U Shaped Bracket with 50mm Fixing Centres
    50+
  • SSBRK-8-90
    SSBRK-8-90 Stainless Steel 316 8mm U Shaped Bracket with 51mm Fixing Centres
    50+
  • DC-SD02
    8mm Rod Dust Cover for 18mm Body Gas Struts
    50+
  • SSMLT-8-200
    8mm Stainless Steel 316 Metal Safety Locking Tube-200mm
More Information
Stroke 200mm
Extended Length 450mm
Rod Diameter 8mm
Body Diameter 18mm
Force Range 50 - 650N

INSTALLATION INSTRUCTIONS

For standard compression gas struts we advise the use of ball joints to alleviate possible side loading, and uneven wearing of the piston rod/seals. Install the strut, piston rod down, for optimum lubrication of the guide and sealing system at all times. Always install the strut in its relaxed state. It is advisable to keep the strut in a single plane of movement. Failure to adhere to this advice may result in a reduced lifespan of the strut. Ensure that the end fittings are tightly fastened onto the thread of the gas struts prior to fitting. If the end fittings require aligning, the piston rod of the gas strut can rotate inside the body (cylinder). Place and hold the piston end fixing on a flat surface, grip the cylinder and firmly twist it until the end fitting is aligned correctly.

FITTING BRACKETS

When utilising a bracket with a ball stud/end, the procedure to fit it to the relevant ball joint fitting is as follows:

  • Remove the retaining clip from the ball socket by rotating it from around the collar of the socket, and then pull it out from the two locating holes.
  • Ensure the ball socket is fully tightened onto the thread of the strut. Then, using a vice or pair of pliers, grip the ball stud and with a rotating motion, remove the ball stud from the socket.

FORCE ADJUSTMENT

  • Fit the gas struts with the cylinder uppermost; this prevents oil escaping while venting, and keeps the internal seals lubricated for optimum lifespan.
  • Using the allen key provided, undo the grub screw anti-clockwise a quarter turn and vent gas for 1 second, retightening the grub screw. Do not over tighten the grub screw.
  • Repeat this process on the second gas strut, venting an equal amount. Only release the pressure in short bursts to avoid venting too much gas. Each 1 second burst will lower the force by approximately 20N - 50N depending on the range.
  • Test the application by attempting to close the panel and repeat the venting process if the struts are still too powerful.
  • Once the gas struts have been adjusted, gently brush the grub screw with washing up liquid. If gas can be seen bubbling through the liquid then the grub screw requires further tightening.

For advice on how to safely mount gas struts call our technical line: 01604 499332.

Gas struts are filled with high pressure nitrogen, they should be protected from damage; never open, modify, drill, weld or subject gas struts to excessive heat.

Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account
Catalogues
  • Download Gas Strut Catalogue - DOWNLOAD
Documents
Struts Accs
  • DC-SD02
Struts Variable
  • NS-SS-V-8-200
Struts End Fittings
  • SSB1
  • SSB3
  • SSB5
  • SSB6
  • SSB7
  • SSC1
  • SSE1
  • SSE2
  • SSE3
  • SSE4
  • SSE5
Struts Brackets
  • SSBRK-052L
  • SSBRK-052R
  • SSBRK-08-90
  • SSBRK-2
  • SSBRK-6
  • SSBRK-7
  • SSBRK-7A
  • SSBRK-8